phone: 02-954-2408-9, 089-514-8111

สินค้าหมด

Crazyflie Nano Quadcopter Kit 10-DOF

sku : EFDV261
Crazyflie Nano Quadcopter เป็นชุด quadcopter แบบ open source ซึ่งได้รับการออกแบบให้มีความยืดหยุ่นในการพัฒนา นอกจากนี้ยังเป็น quadcopter ที่มีขนาดเล็กที่สุดในโลก โดยมีน้ำหนักเพียง 19 กรัม และมีระยะห่างระหว่ามอเตอร์เพียง 9 ซม. เท่านั้น
สมัครเพื่อรับข้อมูลแจ้งเมื่อสินค้านี้กลับมามีในคลังสินค้า

สถานะของสินค้า : สินค้าหมด

฿6,190.00

รายละเอียดสินค้า

รายละเอียด

รหัส : EFDV261
ยี่ห้อ : SeeedStudio
รุ่น : sku: ROB01316M

 

ชุดนี้ไม่รวม Crazyradio 2.4Ghz nRF24LU1+ USB radio dongle with antenna แต่สามารถซื้อแยกได้

The development platform is open source so schematics and firmware/host source code is available at the Bitcraze website as well as a Wiki with design information and details on how to set up the development environment and get started. It’s designed with development in mind and has an expansion header that enables developers to expand the platform as well as good software development support. Due to it’s small size it’s perfect for developing new software and can easily be flown inside. It can lift a payload of up to 5 - 10 g.
 
This is the 10 DOF version of Crazyflie that integrate extra sensors for altitude and heading measurement. There is yet no firmware support for these sensors but they have the potential to enable heading and altitude control. If you want to develop a new algorithm or if you want to be able to use some advanced algorithm that might be created for these sensor you should definitely consider the 10-DOF version.
 
A 2.4 GHz radio chip from Nordic Semiconductors is used for receiving commands and sending telemetry data back to the host computer. The communication with the host is made possible by using the Crazyradio 2.4 GHz USB radio dongle. The Crazyradio can be connected to a PC (with support for Windows and Linux) but also to other hosts that support USB Host or OTG like Android phones. Mac OSX currently has beta support handled by the community.
 
The Crazyflie Quadcopter is shipped pre-programmed but can easily be wirelessly updated via a radio bootloader from a host PC, so no JTAG is required for reprogramming. For advanced development and debugging there’s also an accessible JTAG interface.

This kit requires soldering skills and is not for beginners. It is not a toy and should be handled with care.

 

Summary Features:

  • Small and lightweight, around 19g and about 90mm motor to motor
  • Flight time up to 7 minutes with standard 170mAh Li-Po battery
  • Standard micro-USB connector for charging which takes ~20min for the stock 170mAh Li-Po battery
  • On-board low-energy radio@1mW based on the nRF24L01+ chip. Up to 80m range (environment dependent) when using the Crazyradio USB dongle
  • Radio bootloader which enabled wireless update of the firmware
  • Powerful 32 bit MCU: STM32F103CB @ 72 MHz (128kb flash, 20kb RAM)
  • 3-axis high-performance MEMs gyros with 3-axis accelerometer: Invensense MPU-6050
  • 3-axis magnetometer HMC5883L (compass)
  • High precision altimeter MS5611-01BA03
  • Expansion header 2×10 pins 1.27mm (0.05”) pitch including power, I2C/UART, SPI/ADC. Header also contains ARM Cortex 10-pin JTAG (header not included)
  • 4-layer low noise PCB design with separate voltage regulators for digital and analog supply

 

Product included:

  • Crazyflie control board x 1
  • Duck antenna 2 dBi x 1
  • Motor mounts x 5
  • Coreless DC motors x 5
  • CW propeller x 5
  • CCW propeller x 5
  • LiPo battery x 1
  • 2*5 pins 1.27mm (0.05”) pitch header x 1

 

Information Support:

 

Warranty

 

ข้อมูลเพิ่มเติม

ข้อมูลเพิ่มเติม

ManufacturerSeeedstudio
Country of Manufacture

รีวิวสินค้า

เขียนรีวิวสินค้าของคุณเอง

Only registered users can write reviews. Please, log in or register